Connecting Lady-Comp/Baby-Comp:

Please observe the following sequence:

1. First insert the electrical connection or battery box connection into the socket on the back of the device. Then connect to the mains supply. Press the plus and minus buttons once simultaneously. The correct time appears with a colon in the middle.
2. Lady-Comp/Baby-Comp automatically reverts to this display if no further command is entered for 15 - 30 seconds or when the plus and minus buttons are pressed simultaneously.
3. The thermometer is already inserted in smaller socket.
4. If you are using Lady-Comp/Baby-Comp on battery power, press any button after connecting and the time appears.

Please also observe this sequence for setting the device in operation after an interruption, after a power cut etc.

back to top

Basic Rules For All Input

The same principle applies to the input of any data into Lady-Comp/Baby-Comp.

Operation buttons:

Round button: With the round button, you can change the levels (1). With the round button, you can make the device ready for setting by pressing and holding for 5 seconds (for example to change the time, the alarm time, the date). When the display flashes, it is ready for setting.

Pressing and holding the round button for 5 seconds completes setting.

The flashing stops and there is an acoustic signal to confirm the receipt of the desired input.

Plus button: With the plus button, you can advance and enter data (for example to confirm menstruation).

• One press on the plus button advances the display by one unit.
• Hold the plus button down for fast forward.

Minus button With the minus button, you can go backwards in the display (for example to look at past temperature readings and evaluations).

• One press on the minus button reverses the display by one unit.
• Hold the minus button down for fast reverse.

Data can also be corrected with the minus button.
Level 1: time, alarm time, date, year and test
Level 2: temperature reading, current day in cycle, fertility indicator (current day, previous days and following days)
Level 3 - Baby-Comp only: planning, fertilization day, birth date and gender prognosis

back to top

Necessary Settings Before Commencing:

When you take Lady-Comp or Baby-Comp out of its original packaging, the year, date and time are already correctly set.

1. Setting the alarm

From the time display:

1. Press the minus button once.
2. The alarm setting 07.00 appears on the display.
3. Hold down the round button for 5 seconds. The alarm time flashes.
4. Advance the alarm time using the plus button or reverse the alarm time using the minus button.
5. Press and hold the round button for 5 seconds. The flashing stops and you hear an acoustic signal. The correct alarm setting appears on the display.

The device is ready to take a temperature reading at the alarm time ±3 hours if the alarm is switched on, or at the previous temperature reading time ±3 hours.

2. Switching the alarm on and off (activating)

From the time display:

1. Press the minus button once. The alarm setting appears.
2. Press the minus button again. The bell symbol flashes. You now have a choice:
   • Press the plus button. The bell remains constantly illuminated. You will be woken up at the desired time.
   • Press the minus button. The bell disappears. You will not be woken up.

3. Taking your temperature the next morning

Place the thermometer under the tongue, right at the back, either to the left or the right of the frenulum with the mouth closed. Press any button if the thermometer symbol is illuminated. If the small thermometer symbol flashes, the device is ready for a temperature reading. An acoustic signal indicates the end of the reading. Your temperature reading appears in the display.

After the first temperature reading, the sample values automatically disappear.

4. Fertility indicators:

red = fertile
green = infertile
yellow = learning

5. Menstruation data

After the temperature reading, the "M" symbol flashes.

• If you are menstruating, press the plus button (M remains illuminated).
• If you are not menstruating, press the minus button (M disappears from the display).

Give "M" input on at least three consecutive days. If you have "M" and the machine does not ask you for input, activate "M".

Lady-Comp display

Fertility indicators:
red = fertile
yellow = learning, monophases, no ovulation yet
green = infertile

Alarm indicator: lights up when the alarm is switched on.

Thermometer symbol: lights up during temperature reading time limit and flashes after pressing button.

Menstruation indicator: flashes for menstruation input

• Press "+" for yes
• Press "-" for no

back to top

Operating Lady-Comp and Baby-Comp:

1. Setting the time

From the time display:

1. Press the round button and hold for 5 seconds. The correct time flashes.
   • Advance the time setting with the plus button.
   • Reverse the time setting with the minus button.
2. Press the round button and hold for 5 seconds. The flashing stops. You will hear an acoustic signal to confirm your input.

Attention: If the time is set past 24:00 (either ahead or back), the date is automatically adjusted.

If you will be travelling to other time zones, we recommend the following procedure:

1. Do not take your temperature on the day of travel.
2. Adjust the time on your device to match the local time of your destination upon arrival. (Note crossing midnight will adjust the date automatically, so make sure that you adjust the clock in the proper direction.)
3. Adjust your alarm to your prefered wake up time.
4. Turn on the alarm.
5. Proceed as normal the next morning by taking your temperature as usual. If the device is not ready to take your temperature the next morning, confirm that the alarm was properly turned on and try again the next day.

back to top

2. Setting the date

From the time display:

1. Press the plus button once. The date appears.
2. Hold down the round button for 5 seconds. The date flashes.
   • Press the plus button to advance the date setting.
   • Press the minus button to reverse the date setting.
3. Press and hold the round button for 5 seconds. You will hear an acoustic signal. The date appears on the display.

If the device has already received one or more temperature readings, it is only possible to reverse the date setting by one day. The temperature readings for the current day and the day before are deleted when the date is reversed. You can always advance the date by one day. It is impossible to change the date by accident.

The year is automatically adjusted when you pass December 31. Once the date has been correctly entered, it automatically proceeds correctly, with adjustments for leap years and the year 2000. It does not matter whether the Lady-Comp/Baby-Comp is operated with plug or battery.

back to top

3. Setting the year

From the time display:

1. Press the plus button twice. The year appears in the display window.
2. Hold down the round button for 5 seconds. The year flashes.
   • Press the plus button to advance the year setting.
   • Press the minus button to reverse the year setting.
3. Press and hold the round button for 5 seconds. You will hear an acoustic signal. The year setting appears on the display.

The year setting can only be changed at the beginning. Once temperature readings have been entered, this is no longer possible.

back to top

4. Setting or changing the alarm

From the time display.

1. Press the minus button once. The alarm setting (07.00) appears on the display.
2. Hold down the round button for 5 seconds. The alarm setting flashes.
   • Press the plus button to advance the alarm setting.
   • Press the minus button to reverse the alarm setting.
3. Press and hold the round button for 5 seconds. The flashing stops. You will hear an acoustic signal. The correct alarm setting appears on the display.

back to top

4.1. Switching the alarm on and off

From the time display:

1. Press the minus button once. The alarm setting appears.
2. Press the minus button once more and the bell symbol flashes.
• If you want to be woken up, press the plus button. The bell remains constantly illuminated. You will hear an acoustic signal as a confirmation.
• If you do not want to be woken up, press the minus button when the bell flashes. The bell symbol disappears from the display.

The bell lights up at the same time as the time display to confirm that you will be woken up the next day. If the bell does not light up with the time display, you know that you will not be woken up. This also applies to the following days.

The Lady-Comp/Baby-Comp alarm starts off quietly and gradually becomes louder and louder. The alarm stops when you press any button and take a temperature reading, or automatically after 1 minute.

back to top

4.2. Changing the alarm and temperature reading time

The device is ready for a temperature reading ±3 hours before and after the time of the previous temperature reading. If you choose an alarm time outside these 6 hours, the temperature measuring time is adjusted to ±3 hours in relationship to the new alarm time. This involves activating the alarm.

back to top

5. Taking your temperature, general information

Taking the basal body temperature reliably, every day, is one of the key elements of our system. The basal body temperature is the temperature of the body just after waking up and before getting out of bed or becoming active in any way. The more regularly that you take your temperature, particularly at the beginning, the faster the device gets to know your personal cycle.

• Place the thermometer under the tongue, right at the back, either to the left or the right of the frenulum with the mouth closed.

back to top

5.1 Temperature reading time limit

You can only take a temperature reading once a day and within the temperature reading time limit. The alarm must be activated before the first temperature reading. Lady-Comp/Baby-Comp controls the temperature reading time limit. It comprises 6 hours, beginning and ending three hours before and after the alarm time, or ±3 hours in relationship to the previous temperature reading time if this differs from the alarm time. The thermometer symbol remains illuminated throughout the temperature reading time limit.

• Normally the alarm time and the temperature reading time are both the same. We recommend that you allow Lady-Comp/Baby-Comp to wake you up.
• If you wake up within the temperature reading time limit (e.g. to look after your child), take your temperature.
• If you get up late and the time limit is over, there is no reading for that day.
• If there is no temperature reading for one day, the time limit is left open.

back to top

5.2. Taking your temperature

From the time display:

1. The thermometer symbol is illuminated. It is ready for a temperature reading.
2. Place the thermometer under your tongue, right at the back, either to the left or to the right of the frenulum.
3. To take your temperature, press any button. The thermometer symbol flashes.
4. The display shows temperature readings of 35.20 to 37.59 degrees. When the reading is completed (approx. 30 seconds), you will hear an acoustic signal and the temperature reading appears on the display.

• If the temperature reading is interrupted, e.g. because the mouth is opened, the reading time is automatically extended. The temperature reading flashes to indicate an interruption.
• If the reading indicates that the temperature is too high (over 37.59), an "F" for fever appears on the display.
• If you do not want to take your temperature or you want to interrupt the reading, you can stop the reading by pressing the minus and plus buttons simultaneously. You will hear an acoustic signal. The device stops the reading. There is no temperature reading for this day.
• The tip of the thermometer can be cleaned using warm water. Occasional cleaning is recommended.

back to top

6. Menstruation data

You enter "M" on the days that you have "M". However, this should be on at least three consecutive days.

6.1. At the beginning

In the event that the "M" (menstruation) symbol flashes after the temperature reading:

• If you are menstruating, press the plus button, "M" remains constantly illuminated.
• If you are not menstruating, press the minus button. "M" disappears from the display.

An acoustic signal confirms the input. The day of the cycle alternates in the display.

back to top

6.2. After using the device for some time

When Lady-Comp/Baby-Comp knows your cycle, the device only asks about "M" when menstruation is expected. It begins to ask ("M" flashes) 2 days before. When "M" is finished, Lady-Comp/Baby-Comp stops asking "M" each day.

The first bleeding after stopping the pill is not menstruation but is caused by the withdrawal of the medication. Do not enter "M" for this bleeding.

back to top

6.3. Activating "M"

If you have "M" on a day that Lady-Comp/Baby-Comp does not ask for "M" please activate "M" yourself. From the time display:

1. Press the round button. You see today's temperature reading with the fertility report.
2. Press and hold the round button for 5 seconds.
3. Enter "M" by pressing the plus button.

The following days Lady-Comp/Baby-Comp will ask "M" automatically.

back to top

6.4. Correcting "M"

Incorrect "M" data can be corrected. From the time display:

1. Press the round button once.
2. If you want to correct the "M" data for the previous day, press the minus button. The date of the previous day appears on the display enabling you to enter or cancel "M".
3. Press and hold the round button for 5 seconds. "M" flashes.
   • Say no with the minus button.
   • Say yes with the plus button.

back to top

6.5 Entering "M" at a later time

If you have not taken a temperature reading for some time (e.g. on holiday), but have menstruated during this time, you can enter this at a later time.

1. Go back to the desired date using the minus button.
2. Activate "M", as indicated in point 6.3.

It is only necessary to enter the first "M" day. The device automatically records the following two days.

back to top

7. Fertility display

Lady-Comp/Baby-Comp supplies information concerning fertility on every day of the cycle by using coloured LED's.

• red = fertile
• yellow = learning, ovulation late
• green = infertile

The number of green days slowly increases as the computer learns your cycle.

Yellow is only seldom displayed. If the device does not receive any data for a long period of time or receives information that it cannot evaluate, the number of yellow days increases again.

The reliability of a method of contraception is expressed for medical purposes by the Pearl Index. The Pearl Index indicates how many unwanted pregnancies occur in 100 user years while using a specific means of contraception. A contraceptive pill with a Pearl Index of 1 means that if 100 women use this pill for contraception for one year, one woman will get pregnant in this time. In general, Pearl-Index rates are as follows:

• pill: 0.5-1.0
• IUD: 1-3
• condom 5-15

Right from the beginning, the reliability of Lady-Comp is 0.7 on the Pearl Index. This score comes from the test results collected from 686 women from three countries over a period of two years.

back to top

8. Red LED flashes (2 days)

A flashing red LED indicates the optimum time for fertilization. This means that the device expects ovulation in 1 to 2 days and sexual intercourse on this day is most likely to be successful. This prognosis becomes more and more accurate from cycle to cycle.

back to top

9. Potential fertility display

From the time display:

1. Press the round button once.
2. Press the plus button once to gain access to the potential fertility display.
3. Press the plus button several times to see the expected fertility of the following 6 days.

Every prediction is a statement of probability. The actual level of fertility for the day for which the prognosis is made is shown on the day itself. This means that the prognosis for four days from now may be "green", but if ovulation is late and you are still fertile, the display will show "red" on day 4.

back to top

10. Monophases

If there is no ovulation in a cycle, Lady-Comp/Baby-Comp indicates this to you. When this is the case, the device stays on "red" or, if ovulation is late, it changes to "yellow" until "M" begins.

Monophase cycles can occur up to 20% of the time. If the proportion of monophases is higher, we can provide you with a printout of your cycle to discuss with your gynecologist. Lady-Comp/Baby-Comp printouts can help to diagnose insufficient production of gestagen (CLI).

Please note that when you stop taking the pill, it takes some time before ovulation occurs again and you return to your own cycle.

If you would like to have more information concerning this subject, please contact us.

back to top

11. Data from previous cycles (menstruation data)

If you have information about your cycle, you can enter this data into the device before the first temperature reading. Activate "M" as explained on under point 6.5. It is possible to enter "M" data for up to nine previous, consecutive cycles. For each cycle, it is only necessary to enter the first "M" day, the device automatically saves three days.

back to top

12. Back in operation after an interruption

The date, the year and the time continue to function automatically without connection to electricity or battery. If no temperatures are taken, the temperature reading time limit is left open and must be reset. This involves setting the alarm for the next morning and continuing in the usual way.

To enter "M" data at any time, proceed from the time display:

1. Press the round button once.
2. Press the minus button once. The date appears.
3. Press the minus button or press and hold until you reach the date for which you want to enter your first "M" day (beginning of cycle).
4. Now press and hold the round button for 5 seconds. The date remains constantly illuminated and "M" flashes.

back to top

13. Test mode

Lady-Comp, Baby-Comp, and Pearly provide a function to check the display and all operations of the device, including illumination of the numerical display, the lights that illuminate symbols, and the thermometer sensor.

To access test mode, proceed from the time display:

1. For Lady-Comp/Baby-Comp, press the plus button 3 times. For Pearly, while displaying the time and date, press and hold the (+) plus button until the device starts testing the LCD display.
2. The device now runs through all its symbols independently. The device tests itself and indicates this in the display window. When the test is completed the time appears and the thermometer symbol is illuminated.
3. If you now press the round button, the thermometer flashes and is ready for a reading.
   
4. You can now take a test temperature if you wish. Test temperatures are not recorded to memory; it only checks the sensor's function. To interrupt a reading or to leave the test mode, press the minus and plus buttons simultaneously and you will be returned to the time.

back to top

14. Deleting memorized data

To erase data from devices sold prior to April 2004, proceed with the instructions below from the time display. For devices sold on or after April 2004, procceed with the directions after entering the test mode. (See 13. Test mode)

1. Press and hold the round button, the minus button, and plus button simultaneously. Hold for 5 seconds.
   • If the display becomes lighter or darker while you are trying to cancel data, this means that you did not press the plus and minus buttons simultaneously.
   • If the display is turned off, this again means that you did not press the plus and minus buttons simultaneously. Please start again from the beginning.
2. An "L" appears on the display panel, with a "9" on the right (eg. "L-09" or "L--9"). Let go of the buttons.
3. You must count down this "9" to zero by pressing the minus button 9 times. The cancellation process is interrupted if you touch any other button.
4. Cancellation takes place automatically at zero. There is an acoustic signal. Then the current time appears on the display.

This method makes it impossible to delete memorized data by mistake. After deleting the data, the device returns to factory mode and will display the sample values (e.g. temperature 36.65 or 97.97). After the first temperature reading, the sample data is automatically removed again.

back to top

15. Analysis of the cycle

Proceeding from the time display:

1. Press the round button once and the temperature reading of the day appears. This display alternates with the current day of the cycle.
2. Press the minus button once. The date of the previous day appears. This display alternates with the temperature reading of the day in question.
   • The minus button enables you to go back.
   • The plus button enables you to go forward.

You can recall all the previous temperature readings for up to 150 days by pressing the minus button again and again. If you do not press any button for 30 seconds or when you press the plus and the minus button simultaneously, the recall process stops.

back to top

16. Print-out and evaluation

In the event of difficulties with your cycle or conception, a printout and evaluation can usually provide valuable information for you and your gynecologist, e.g. concerning the follicle phase, ovulation, the luteal phase, and pregnancy. If you are interested in receiving a detailed analysis of your cycle and a print-out of the data stored in the device, please contact us to make arrangements.

back to top

17. Pregnancy display

Lady-Comp indicates a probable pregnancy on the 15th day after conception by the simultaneous flashing of the red, yellow and green indicators. The pregnancy is confirmed from the 18th day following fertilization by the simultaneous constant illumination of the red, yellow and green indicators.

back to top

18. Battery operation

For Lady-Comp/Baby-Comp devices purchased prior to April 2004, you can operate on battery power by placing 8 AA cells in your battery pack. On devices purchased on or after April 2004, there is now a built-in rechargable battery. It automatically recharges over 48 hours when you plug it in using the wall plug supplied with it.

All the operations available while the device is plugged into to a wall plug, are also possible while using batteries as power source. If no button is pressed while operating on batteries, Lady-Comp/Baby-Comp automatically turns itself off after 15 - 30 seconds. The display remains off and only lights up when the alarm wakes you up or if you press a button to turn it on.

If, when using batteries on older devices, the display shows "BA-", then it is time to change the batteries. (For best performance, we recommend changing batteries after 3 weeks.) On newer models, "BA-" means it is time to recharge the internal battery for 48 hours. (We recommend leaving the device plugged in at all times on your night table while at home. This will insure full power if you travel on short notice.)

back to top

19. Power supply

Lady-Comp/Baby-Comp comes with a universal power adapter. The adapter includes an insert for your local configuration that we supply based on the delivery address. Since the new Lady-Comp/Baby-Comp comes with a built in battery that lasts 3 weeks on a full charge, inserts for other countries you may visit while traveling are only needed if you will be away for more then 3 weeks.

back to top

20. No risk of loss of data

In the event of a power cut, flat batteries or when changing batteries, there is absolutely no risk of losing the data memorised in the Lady-Comp/Baby-Comp or the data concerning menstrual cycles.

back to top

21. Changing display brightness

Any change of brightness to the display applies only to the "stand by" time display. When you begin to use the device, the display shows the normal full degree of brightness and is then reduced to the desired level when the device enters "stand by".

To set stand by brightness levels, proceed from the time display:

1. Press and hold the round button.
   • Press the plus button to brighten the display.
   • Press the minus button to darken the display.

The display gets darker if you are doing something wrong.

The display can also be completely turned off in stand by mode, by adjusting the dim level. This setting can be achieved by pressing the minus button repeatedly until you hear an acoustic signal. The device now functions as if it were using battery power, even if it is plugged directly in to the wall.

back to top

22. Testing the sensor device

See 13. Sample values, test, trial readings

back to top

23. Summer and winter time

Set the time forward or back to summer or winter time. The date changes automatically when the clock passes 24.00.

back to top

Baby-Comp display

Fertility indicators: (from left to right)

• red = fertile
• yellow = learning, monophases, no ovulation
• green = infertile

Alarm indicator: lights up when the alarm is switched on.

Thermometer symbol: lights up during temperature reading time limit and flashes after a button has been pressed.

Menstruation indicator: flashes for input

• Plus button = yes
• Minus button = no

Birth indicator: date flashes showing the possible date of birth, remains constantly illuminated for confirmed pregnancy.

Conception indicator: flashes on best days for conception and remains constantly illuminated for confirmed pregnancy.

Female gender prognosis indicator: lights up if there is more likelihood of your conceiving a girl.

SI data: flashes for input about sexual intercourse.

Male gender prognosis indicator: lights up if there is more likelihood of your conceiving a boy.

back to top

24. Pregnancy planning

Baby-Comp shows you the optimum time for you to get pregnant. You can see the optimum days to get pregnant flashing in the display window on the first days of a new cycle. Just two days per cycle are considered to be optimum. These days have no significance for the sex of the offspring and so the "boy" and "girl" symbols flash together with the date.

• In order to plan for a boy, only have intercourse on the day on which just the "boy" symbol is shown. The "boy" symbol lights up one day before the first optimum conception day.
• If your preference is for a girl, only have intercourse on the day on which just the "girl" symbol is shown. The "girl" symbol lights up one day after the second optimum conception day.

Proceeding from the time display:

1. Press the round button twice. The current date appears on the display.
2. Press the minus button and you will see the optimum conception date and gender preference, along with the "sperm" symbol.
3. Then press the plus button twice and you will see the predicted date of birth and gender prognosis, along with the "baby" symbol.

Attention: Before ovulation, the dates and symbols flash. After ovulation, they are constantly illuminated. If no prediction is possible, "--:--" appears on the display.

back to top

25. Gender prognosis

During a possible or confirmed pregnancy, Baby-Comp indicates whether you can expect to have a boy or a girl. This is on condition that you entered SI input on the morning after intercourse. Both the boy and girl symbol will appear if intercourse took place on days on which it is equally likely for a boy or a girl to be conceived. This also applies if no SI was entered.

Proceeding from the time display:

1. Press the round button twice. The current date appears on the display.
2. Press the minus button and you will see the conception date with the symbols "boy" and/or "girl" and the sperm symbol.
3. Press the plus button twice and you will see the estimated date of birth with the symbols "boy" and/or "girl" and the birth symbol.

back to top

26. "SI" input

If you are planning a pregnancy and are interested in having a gender prognosis, inform Baby-Comp when sexual intercourse (SI) took place. Enter "SI" data the following morning after taking a temperature reading.

Proceeding from the time display:

1. Press the round button twice to get into the planning level.
2. Press and hold the round button for 5 seconds. The "SI" symbol flashes.
   • Say yes for "SI" by pressing the plus button. The "SI" symbol remains constantly illuminated.
   • Say no for "SI" by pressing the minus button. The "SI" symbol stops flashing.
3. An acoustic signal confirms the input.

If the device has received "SI" information, it indicates on the fertile days whether there is more likelihood of conceiving a girl or a boy in the event of fertilization. (See 24. Pregnancy planning)

back to top

27. Correcting "SI" input

If you want to cancel incorrect "SI" input, you must do this on the same day. (See 26. "SI" input, but press the minus button to say no "SI" input.)

back to top

28. Pregnancy display

Baby-Comp distinguishes between three pregnancy stages:

1. Possible pregnancy after 4-5 days. Red, yellow and green alternate individually. (if SI data has been entered).
2. Probable pregnancy after 15 days. Red, yellow and green flash simultaneously.
3. Confirmed pregnancy after 18 days. Red, yellow and green are constantly illuminated.

Baby-Comp indicates a possible pregnancy by the 4th-5th day after fertilisation. This very early indication can be made when SI (sexual intercourse) data has been entered on the following morning after the temperature reading and a possible pregnancy could be calculated. The fertility symbols red, yellow and green alternate.

After the fifteenth day Baby-Comp automatically indicates a "probable pregnancy". The fertility symbols red, yellow and green flash.

If the likelihood of pregnancy is confirmed, there is a further display from the 18th day after fertilisation. All three colours are constantly illuminated.

The conception and birth date can be called up onto the display via the planning level. (See 29. Conception date and birth date)

(For gender prognosis, see 25. Gender prognosis)

back to top

29. Conception date and birth date

After ovulation has been recognised, Baby-Comp indicates the possible conception and birth dates in the planning level. These displays can be called up whether a pregnancy has taken place or not. Proceeding from the time display:

1. Press the round button twice. The current date appears on the display.
2. Press the minus button and the date of conception appears.
3. Press the plus button twice and the estimated date of birth appears.

Attention: Before ovulation, the dates and symbols flash. After ovulation, they are constantly illuminated. If no prediction is possible, "--:--" appears on the display.

back to top

30. Pregnancy confirmation

In the event of a confirmed pregnancy, the conception date and the date of birth remain constantly illuminated. We recommend that you continue to take temperature readings every morning during the first months. Baby-Comp keeps an eye on the development of the early pregnancy. Now is the time to make an appointment with your gynaecologist.

back to top

31. Back in operation after pregnancy

The risk of becoming pregnant during the first six months after giving birth is low (2%) provided that you are fully and frequently breast-feeding your baby. After this and in all other cases, we recommend you to recommence temperature readings 6 weeks after the birth or even earlier. At first Baby-Comp shows "yellow". Slight fluctuations in temperature indicate that the normal cycle is reestablishing itself. Baby-Comp begins to show the usual fertility display.

back to top